Free 200-105 Questions for Cisco Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0) 200-105 Exam as PDF & Practice Test Engine

Exam Code/Number: 200-105
Exam Name/Title: Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0)
Certification Provider: Cisco
Corresponding Certification: ICND2

Exam Questions: 775
Updated On: Jul 24, 2026

Question #1

In the Frame Relay network, which IP addresses would be assigned to the interfaces with point- to-point PVCs?

A. DLCI 16 192.168.10.1/24
DLCI 17 192.168.10.2/24
DLCI 99 192.168.10.3/24
DLCI 28 192.168.10.4/24

B. DLCI 16 192.168.10.1/24
DLCI 17 192.168.10.1/24
DLCI 99 192.168.10.2/24
DLCI 28 192.168.10.3/24

C. DLCI 16 192.168.10.1 /24
DLCI 17 192.168.11.1/24
DLCI 99 192.168.12.1/24
DLCI 28 192.168.13.1/24

D. DLCI 16 192.168.10.1/24
DLCI 17 192.168.11.1/24
DLCI 99 192.168.10.2/24
DLCI 28 192.168.11.2/24

Discussion 0

Correct Answer: D Vote an answer

Explanation: Only visible for ExamDiscuss members. You can sign-up / login (it's free).

Question #2

When you enable PortFast on a switch port, the port immediately transitions to which state?

A. Listening

B. Learning

C. Blocking

D. Forwarding

Discussion 0

Correct Answer: D Vote an answer

Question #3

Which two statements about static NAT translations are true? (Choose two.)

A. They allow connections to be initiated from the outside.

B. They require no inside or outside interface markings because addresses are statically defined.

C. They can be configured with access lists, to allow two or more connections to be initiated from the outside.

D. They are always present in the NAT table.

Discussion 0

Correct Answer: A,D Vote an answer

Question #4

Which result occurs when you configure the standby preempt command on an HSRP router that has the same priority as the active router and a higher IP address?

A. The router immediate becomes the active router because it has the highest configured ip address

B. The router fails to become the active router under any circumstances

C. The router becomes the active router only when the current active router fails

D. The router become the active router only when another router trigger renegotiation of the active router

Discussion 0

Correct Answer: A Vote an answer

Question #5

What are two characteristics of Frame Relay point-to-point subinterfaces? (Choose two.)

A. They emulate leased lines.

B. They require the use of NBMA options when using OSPF.

C. They require a unique subnet within a routing domain.

D. They are ideal for full-mesh topologies.

E. They create split-horizon issues.

Discussion 0

Correct Answer: A,C Vote an answer

Explanation: Only visible for ExamDiscuss members. You can sign-up / login (it's free).

Question #6

The command show frame-relay map gives the following output:
Serial 0 (up): ip 192.168.151.4 dlci 122, dynamic, broadcast, status
defined, active
Which statements represent what is shown?(Choose three.)

A. broadcast indicates that a dynamic routing protocol such as RIP v1 can send packets across this PVC

B. 192.168.151.4 represents the IP address of the local serial interface

C. DLCI 122 represents the interface of the remote serial interface

D. active indicates that the ARP process is working

E. DLCI 122 represents the local number used to connect to the remote address

F. 192.168.151.4 represents the IP address of the remote router

Discussion 0

Correct Answer: A,E,F Vote an answer

Explanation: Only visible for ExamDiscuss members. You can sign-up / login (it's free).

Question #7

Which IEEE standard does PVST+ use to tunnel information?

A. 802.1s

B. 802.1w

C. 802 1q

D. 802.1x

Discussion 0

Correct Answer: C Vote an answer

Question #8

From which PPPoE server configuration does a PPPoE client get an IP address?

A. virtual-template interface

B. dialer interface

C. AAA authentication

D. DHCP

Discussion 0

Correct Answer: A Vote an answer

Question #9

Which command do you enter so that a switch configured with Rapid PVST + listens and learns for a specific time period?

A. switch(config)#spanning-tree vlan 1 priority 4096

B. switch(config)#spanning-tree vlan 1 max-age 6

C. switch(config)#spanning-tree vlan 1 hello-time 10

D. switch(config)#spanning-tree vlan 1 forward-time 20

Discussion 0

Correct Answer: D Vote an answer

Question #10

Which component of an IPv6 OSPFv3 connection must be configured in IPv4 format?

A. Secondary interface

B. Router ID

C. Neighbor address

D. Primary interface

Discussion 0

Correct Answer: B Vote an answer

Question #11

Which three options are types of slow VLAN connectivity? (Choose three)

A. slow broadcast domain connectivity.

B. slow default gateway connectivity.

C. slow routing domain connectivity.

D. slow application domain connectivity.

E. slow inter VI AN connectivity.

F. slow collision domain connectivity.

Discussion 0

Correct Answer: A,E,F Vote an answer

Free 200-105 Questions for Cisco Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0) 200-105 Exam as PDF & Practice Test Engine

Download Free Cisco 200-105 Demo