Free NS0-507 Questions for Network Appliance NetApp Certified Implementation Engineer - SAN, Clustered Data ONTAP NS0-507 Exam as PDF & Practice Test Engine
You are asked to create a volume and lun, both of which need to be thin provisioned.
In this scenario, which two statements are correct? (Choose two.)
In this scenario, which two statements are correct? (Choose two.)
Correct Answer: A,C
Vote an answer
Referring to the diagram shown in the exhibit, what will happen when the SAS adapter in slot 2 on Node A fails?
Correct Answer: C
Vote an answer
A customer has 1 TB volume with space guarantee set to volume. Two 100 GBs LUNs are created in the volume with LUN reservation enabled and no snapshot copies exist.
In this scenario, how much space will be shown as used in the volume?
In this scenario, how much space will be shown as used in the volume?
Correct Answer: A
Vote an answer
You have a 2-node FAS900 cluster with six FC LIFs per node.
In this scenario, which two methods will limit the total number of paths to eight paths per
LUN? (Choose two.)
In this scenario, which two methods will limit the total number of paths to eight paths per
LUN? (Choose two.)
Correct Answer: A,C
Vote an answer
You have an AFF A300 system that serves FC LUNs. The LUNs are replicated to a disaster recovery site that has a FAS8200 system that is running SATA drives. There are no FC or FCoE capable switches at the disaster recovery site.
In this scenario, which three actions are required to test the disaster recovery LUNs on the
Ethernet switches? (Choose three.)
In this scenario, which three actions are required to test the disaster recovery LUNs on the
Ethernet switches? (Choose three.)
Correct Answer: B,C,D
Vote an answer
Your vSphere administrator asked you to create an additional 5GB boot LUN for their new
ESX1 installation. To complete this request, you have entered the following CLI commands:
lun create -vserver svm1 -volume boot -lun exsi_1 -size 5G -ostype vmware igroup create - vserver svm1 -igroup esxi_1 -protocol fcp -ostype vmware -initiator 50:01:43:80:05:68:5f:
B6
However, the vSphere administrator has reported that they are unable to see the newly configured LUN.
What must you do to solve the problem?
ESX1 installation. To complete this request, you have entered the following CLI commands:
lun create -vserver svm1 -volume boot -lun exsi_1 -size 5G -ostype vmware igroup create - vserver svm1 -igroup esxi_1 -protocol fcp -ostype vmware -initiator 50:01:43:80:05:68:5f:
B6
However, the vSphere administrator has reported that they are unable to see the newly configured LUN.
What must you do to solve the problem?
Correct Answer: B
Vote an answer
An administrator has an existing FAS3210 running DATA ONTAP 8.2.4 7-mode. They have recently purchased and installed a new AFF A300 ONTAP cluster and need to non- disruptively migrate FC LUNs from the 7-mode system to the new cluster. The administrator has cabled the FC interfaces shown in the exhibit.
In this scenario, which additional cabling will be needed on the AFF A300 to support foreign
LUN import 7-mode?
In this scenario, which additional cabling will be needed on the AFF A300 to support foreign
LUN import 7-mode?
Correct Answer: B
Vote an answer
Which NetApp resource would you use to validate the maximum number of FC hops that are supported by a switch vendor?
Correct Answer: D
Vote an answer
You notice that reporting nodes are not mapped on a LUN in a 4-node cluster that originally ran an older version of ONTAP. In this scenario, which command would you use to add only the local HA pair to the reporting nodes for the /vol/data/lun1/LUN?
Correct Answer: D
Vote an answer
0
0
0
10